Example photo by Pete Alexopoulos on Unsplash, not our project
Harrow · London
Alcove units in Queensbury, Harrow
In Queensbury, we design alcove units around the room you actually have. We design your alcove unit at a visit to your home, make it in our workshop and fit it.
- Units that sit well with original features
- Everyday clutter left on show
- Old alcove cupboards that have seen better days
Need alcove units in Queensbury?
How we make alcove units for Queensbury
In a typical Victorian or Edwardian terrace, the chimney breast leaves an alcove on either side of it. Built-in alcove units put that space to work as cupboards and shelving that sit as part of the room. Where a room in Queensbury has a pair of alcoves, we design a unit for each one after we have measured them at a design visit. If your home has everyday clutter left on show and bare alcoves beside the fireplace, that is what alcove units are for, made from birch ply and moisture-resistant MDF, painted by hand or sprayed.
Ceilings in interwar houses tend to be lower than in Victorian ones, and the proportions of alcove units are set to match. Where your home is one of the interwar houses or semis that are a big part of the housing around Queensbury, the cornice may be plain or missing, so the furniture can run straight to the ceiling. Any skirting is cut around neatly.
The furniture is made at our workshop after you have had the quote and decided to go ahead. It describes the design, the materials and the finish agreed at the visit, so you can check every detail beforehand.
- Location
- Queensbury (HA3, NW9, HA7)
- Borough
- Harrow
- Cost
- Quoted for your room
- How it starts
- We visit, measure, then quote
- Made
- Workshop-made, then fitted
- Materials and finish
- MDF and birch plywood, painted
- When we fit
- Weekdays, and Saturdays by prior arrangement
- Enquiries
- Our contact form
- Page updated
- 27 October 2026
Living-room storage in Queensbury
In the neighbourhood around Queensbury, the largest groups of homes date from between 1919 and 1939 (about 80%) and the years since 2000 (about 8%), according to Valuation Office Agency council tax figures (2025). We take that into account at the measuring visit, since older and newer walls take different fixings. Queensbury is partly covered by a conservation area, going by Historic England’s data. Fitted furniture inside a house doesn’t normally need planning permission in a conservation area, as the controls are mainly about the outside of buildings. Your council can advise if you’re unsure. The ULEZ, run by TfL, takes in all of London, so Harrow is inside it. That includes the vans that bring and fit furniture in Queensbury. Access and parking are talked through at the measuring visit.
For families living near Glebe Primary School, shelving with deep cupboards below keeps books, games and school things in one place. Close to Roe Green Park? A room that looks out on trees deserves a design that leaves the window alone.
Queensbury is part of the London Borough of Harrow, about 3 miles south-west of Harrow. Anywhere in Queensbury, the process is the same: we visit and measure, send a quote in writing, make the furniture in our workshop and fit it. We list Queensbury among 20 places we cover in Harrow.
In HA3, NW9 and HA7, the process is the same as anywhere else in London. If your home is on a street like Glebe Lane, Kenton Road and Turner Road, or close by, we can visit to measure up for alcove units. Queensbury sits close to the A4006 and A4140. Close by, we also work in Kingsbury (1 mile south-east), Preston (1 mile south), Colindale (2 miles east), West Hendon (2 miles east) and The Hyde (2 miles east). Other parts of Harrow we cover include Harrow (3 miles south-west), Stanmore (2 miles north), Hatch End (4 miles west), Harrow Weald (2 miles west), Wealdstone (2 miles west) and Greenhill (2 miles west).
What’s near Queensbury
Around Queensbury, we cover homes near Whitchurch Junior School, The New Moon pub and Canons High School. The nearest railway station is Kenton station, about 1.3 miles south-west of the centre. A little further out are Broadwalk Centre (1.6 miles north-east) and Edgware Community Hospital (1.3 miles north-east). Open spaces near Queensbury include Masons Field.
Also near Queensbury
What else we make in Queensbury
Do you need alcove units in Queensbury?
Where a fireplace has been blocked up or removed, the chimney breast can look bare. A pair of alcove units frames it and gives the wall a sense of order.
We’re often asked to help with:
- Tired cupboards in the alcoves
- Somewhere to keep books and records
- A desk that tucks into an alcove
- Storage that suits a period room
Headstone Manor, about 2.7 miles west, is one of the historic houses in the wider area. For a period home anywhere nearby, walls that bow and floors that slope are why alcove units are scribed to fit rather than pushed into place.
Questions to ask before you hire anyone
- Will the doors close with even gaps?
- Whether they can show you real projects they’ve done
- Whether they measure the room themselves
- Will other trades be needed, and who arranges them?
What happens on fitting day
Period rooms often have skirting boards, picture rails, cornices or coving for the furniture to meet. On fitting day, we cut and scribe the furniture around these details, so it sits neatly against the room. How long fitting takes depends on the size and number of units, and we confirm the fitting days in your quote. Clearing the room and the way in beforehand helps the day run well. Fitting day starts with protecting the floors and setting out the pieces. Each piece is levelled, scribed where the wall wanders and fixed to suit the wall.
- To begin, use our contact form; a brief note on the room and the alcoves is enough, and mention if you live in a flat or up a few flights of stairs.
- At the design visit we measure the alcoves and also the way in: the front door, the hall and any stair turns. Parking is worth mentioning too, since a van often needs a permit or a paid bay in London.
- Your written quote sets out the design, materials and finish.
- The units are made at our workshop from moisture-resistant MDF and birch plywood, in sections sized to come through your door.
- We carry the sections in, assemble them in the alcoves and scribe them to the walls.
How to prepare
- Mention any parking restrictions on your street
- Clear the walls of pictures and shelves
- Clear the hallway and stairs so the sections can come through
Getting a quote
Because every job is different, the cost is set out in a written quote after the visit. Because every room is different, the quote comes after the design visit. For a quote, tell us about the room on our contact form.
Read more
Made for the room, or bought in a box?
A bespoke unit takes longer to arrive than something from a shop: it needs a design visit, a quote and time in the workshop. What you get is a unit planned for your alcove, not the nearest catalogue size. Ready-made units come in standard depths that rarely suit every space, so they can stick out too far or waste space behind. Fitted furniture is made to the depth the space can take.
Every room is priced on its own, because the size, the layout and the finish all vary. A spray finish and a hand-painted finish involve different work, and that shows in the price. You’ll see the figure in your written quote, after the design visit.
Why us?
- Made in our workshop, then fitted in your home
- Saturday visits and fitting by arrangement
- Built around your room
- 300+ projects completed
Take a look at our comparison of bespoke and off-the-shelf and how to compare quotes.
Questions we’re often asked
Can you fit furniture in a home close to Kenton station?
Yes, homes across Harrow and the rest of London are within the area we cover. To get started, you can get in touch through our contact form with some details about the room, and tell us about parking and access at the same time.
Can you make alcove units for a home in Queensbury?
Yes. We cover all of Harrow and the rest of London, and Queensbury is part of that. We start with a design visit to measure the room and talk through what you need, followed by a quote.
Can you fit a desk into an alcove?
Yes. One alcove can take a desk with shelves above and a drawer or cupboard beneath. Height and depth are agreed with you, with a way planned for cables to reach the sockets.
Should I send pictures?
Yes. They give us a feel for the space before we visit, along with rough sizes. Show anything the furniture has to work around, like radiators or sockets.
Can you add sockets inside the units?
We do not do electrical work. New or moved sockets are a job for your electrician, ideally before fitting, and some electrical work in homes is covered by Part P of the Building Regulations. We can plan cut-outs and cable routes in the units around them.
Can alcove units be fitted to uneven walls?
Yes. Few alcoves in older houses are truly square, so we scribe each unit to follow the wall. A plinth or adjustable feet set it level on a sloping floor.
Bespoke or off-the-shelf?
What you pay for with bespoke is mainly the fit: edges scribed to the wall, a level base on a sloping floor and a neat line where the furniture meets the ceiling. Off-the-shelf furniture cannot typically do that in an older room.
A confident DIYer can manage simple shelves or a standard wardrobe in a square room. Sloping ceilings, uneven floors and lath-and-plaster walls make it harder, because scribing and the right fixings start to matter.
Flats, conversions and leaseholders
A lot of London’s terraced houses are now converted flats, and that often means a shared hallway and a tight turn on the stairs. We plan the size of each section around it, after measuring the route at the design visit.
If your flat is leasehold, check your lease before fixing furniture to the walls. Some leases need the building owner’s consent for alterations, and that’s best sorted before fitting day. We cannot give advice on leases, so check it yourself or ask your managing agent.